How To Install Disk Brake On Bicycle

Disc brakes: How to replace the discs

The pads in disc brakes are the parts of the brake that will clothing out the fastest. But when a disc brake is used intensively and oft you also have to replace the disc i time. You know when to replace this part every bit the disc has become thinner than 1,7mm. You lot don't need to go to the bicycle shop, but can do it easily yourself. How to do this? We explicate it in this blog.

6-commodities or a Centerlock disc?

How to replace a 6-commodities disc restriction

Necessities:

• BBB Torx sleutel /BTL-46
• BBB MultiTool / (To adjust your drive on the go)

one. Remove the bicycle from your cycle

To supplant the disc of your disc brakes well, you need to remove the wheel from your bike. Open the quick-release organisation (when this is the way your wheel is attached to the wheel) and remove the wheel.

2. Remove the old disc

Remove the old disc that is attached to the hub of the wheel with 6 bolts. Utilise a torx key to do this.

three. Mount the new disc

Place the new disc on the hub of the wheel. Tighten the bolts one by one. Make sure you tighten them proportional. Start with i bolt and keep with the reverse one every fourth dimension. Lubricate the bolts a bit before tightening. This to provide dirt, water and sand to pollute the bolts. Pay attention to the bending of the disc, information technology has to be attached parallel to the wheel.

4. Mount the wheel dorsum on the bike

If yous are sure that the disc is mounted straight on the wheel, you tin can mountain information technology on the bike again. Check if the disc is attached straight by turning the wheel with your hand.

How to supersede a Centerlock disc

If y'all have a bicycle with a Centerlock disc brake. Replacing the disc is even more easy. Considering with this technique the disc will always be mounted parallel to the wheel.

Necessities:

• BBB Hex Tool (4 of 5mm) /BTL-45
• BBB MultiTool / (To adjust your drive on the go)

ane. Remove the wheel from your cycle

To supercede the disc of your disc brakes well, y'all need to remove the wheel from your bike. Open the quick-release system (when this is the way your wheel is fastened to the wheel) and remove the bike.

2. Remove the old disc

Use the BBB BracketGrip or some other tool to remove the old disc from the hub of the wheel. Place the tool on the washer and plow. When it comes lose you tin selection the disc of the bike.

three. Mountain the new disc

Place the new disc on the hub of the wheel. You don't have to pay attention to the angle of the disc. But, brand certain the right side of the disc is turned to the outside. Now attach the washer and mount the disc.

4. Use our adapter when using BBB discs

Did you buy discs from us merely you have a bike with Centerlock organization? In this case yous will need the CenterFit (Bbs-xc) adapter to mount the disc to the wheel. Place the disc in betwixt the black and silverish part of the adapter and adhere it to the wheel.

v. Mount the new disc

Place the new disc on the hub of the cycle. Tighten the disc on about 40Nm, with reasonable power. Advantage of this system is that the disc will always be parallel on the wheel.

6. Mount the wheel back on the bike

You lot don't demand to check if the disc is mounted direct on the wheel, but exercise bank check if the wheel runs smoothly.

Disc brake pads need to be replaced equally well

Likewise the disc you need to replace the disc brake pads even more often. But, when you lot need to replace them and hoe to practice this. You read all most information technology in this blog: How to supervene upon disc brake pads? Do your brakes make a squeaking sound? In this instance it is possible that they are wrong aligned. Do yous desire to know how to arrange your disc brakes: How to adjust a disc brake?

Source: https://bbbcycling.com/uk_en/how-to-replace-disc-brakes

Posted by: patrickbeciond.blogspot.com

Share this post