How To Repair Mavic Pro Gimbal
Introduction
Follow this guide to remove the gimbal/camera of the DJI Mavic Pro M1P. You volition need to remove the battery and upper vanquish earlier accessing the gimbal. Before attempting, be aware that you will need to scrape off some plastic adhesive that covers a couple screws. Tweezers and 3 different sized screwdrivers are required to access the gimbal/camera for this guide, equally described below in the tools department.
-
-
Grab both sides of the battery.
-
Pinch the releasing buttons on both sides of the battery.
-
Lift the bombardment up and out.
-
-
-
Remove the six 5mm ane.5 Hex screws past turning the screwdriver counterclockwise.
-
-
-
Flip the drone over so that the gimbal is facing up.
-
Remove the two 4mm 1.v Hex screws most the gimbal case by turning the screwdriver counterclockwise.
-
Remove the two 5mm 1.5 Hex screws near the gimbal case by turning the screwdriver counterclockwise.
-
-
-
Remove the 2 small-scale panel pieces near the gimbal case with the tweezers.
-
-
-
Remove the six 5mm one.5 Hex screws that are nether the panel pieces by turning the screwdriver counterclockwise.
-
-
-
Flip the drone dorsum over so the upper shell is facing upward.
-
Pry off the upper shell with a nylon spudger.
-
-
-
Remove the white connector at the back of the flight controller board by gently pulling at the base.
-
-
-
Remove the 1 5mm JIS #0 screw from the pocket-size micro controller board at the front of the DJI Mavic Pro by turning counterclockwise.
-
-
-
Pull the cord and micro controller board away from the front end of the DJI Mavic Pro using tweezers.
-
-
-
Betrayal the ii small ZIF connectors near the front of the board by removing the plastic coverings.
-
Then, remove the two ZIF connectors under the coverings using a nylon spudger.
-
-
-
Remove two 6mm JIS #00 screws from the plastic board comprehend at the forepart of the DJI Mavic Pro.
-
-
-
Flip the DJI Mavic Pro over.
-
Gently press the latch for the Gimbal comprehend.
-
Pull the encompass off.
-
-
-
Flip the DJI Mavic Pro back over, with its pinnacle side facing up.
-
Remove the two ZIF connectors located behind the plastic covers by using a nylon spudger.
-
-
-
Gently remove the ability cable connector located to the left, behind the gimbal lath, past pulling up on the white base of operations.
-
-
-
Scrape abroad the plastic adhesive covering the two 5mm JIS #000 screws connected to the gimbal board.
-
Remove the two 5mm JIS #000 screws from the gimbal board by turning the screwdriver counterclockwise.
-
-
-
Remove the two 7mm JIS #00 screws at the very forepart of the DJI Mavic Pro by turning the screwdriver counterclockwise.
-
Careful when removing these screws the photographic camera or whatever remains of your camera assembly may drop
-
-
-
Flip the DJI Mavic Pro over, with the camera facing you lot.
-
Gently pull the gimbal/camera assembly upward and out.
-
Conclusion
To reassemble your device, follow these instructions in opposite order.
Embed this guide
Choose a size and copy the code below to embed this guide as a pocket-size widget on your site / forum.
Preview
How To Repair Mavic Pro Gimbal,
Source: https://www.ifixit.com/Guide/DJI+Mavic+Pro+Gimbal-Camera+Replacement/114214
Posted by: patrickbeciond.blogspot.com
0 Response to "How To Repair Mavic Pro Gimbal"
Post a Comment